Step - by - Step How to

Ecentric locking collar bearing replacement

This is another addition to our new how to series, we will ba adding more every week, so check back often. You may also e-mail suggestions for future how - to's to. richard@route6x6.com


Axle and bearing replacement is a common maintenance replacement item to all AATV's. Argo, Max, Hustler and others all used simular systems and concepts, some have the inner bearing in a sheet metal flange, as shown below on the outer bearing, others ride on a single brass bushing on inside. Some axles are splinned but the replacement concept is the same.

Machine shown in a 1999 MAX II, Solid round axles with inside bearing and disc brakes.

We at ROUTE6x6 and RICHARD"S RELICS stock and supply all bearings, axles, flanges, brakes, sprockets for most machines at discount prices Click to go to CHASSIS PARTS PAGE

   

Bearing replacement

   
Always disconnect negetive battey cable before servicing your machine.

First remove tire assembly and jack up machine, clean bearing flange area as shown in photo.

Yellow pointer is showing the set screw hold in the ecentric locking collar bearing. Note there are two holes in this collar, one with set screw, other one is drilled but untaped.

Remove set screw ( yellow pointer) Note: There may be another set screw under the top one. Remove both with the correct size allen key tool.


Click on PHOTOS to see larger view

 


You are trying to loosen the locking collar from the inner race of bearing, this collar's purpose is to "lock" the inner race of the bearing to the axle, this prevents axle from coming out or spinning inside the bearing. It does this by bearing inner race being ecentric shaped with the locking collar round, when you turn the two against each other, they "lock" together.

After removing set screw (s) Turn bearing untill you see the drilled untaped hole, shown by yellow pointer. Take a punch and a hammer, tap (hard) on punch, held in drilled hole, first try clockwise (CW) if the collar does not come loose tap counter clockwise (CCW) untill collar spins free of bearing inner race.

Locking collar is now free and spins on axle.



Click on PHOTOS to see larger view



Working back outside machine. Tap out axle with a hammer


Note: Sounds easy, but rust and damage can keep axle from coming out, apply lots of PB Blaster and let the axles soak, where they go through bearings and sprockets.





Axle coming out of outer bearing







Click on PHOTOS to see larger view


To replace outer bearings, note location of the three nuts holding sheet metal flanges to the body, remove these bolts as shown by the yellow pointer.

 

Note: Some machines will have four bolts

Note: See how bearing is installed with inner race lip outwards, this is what the locking collar "holds" on to.


With nuts removed, you will see you have two flanges with a bearing between the two flanges, seperate the flanges with a screw driver, remove outer one as shown.

 

 

Note: The red grease. Be sure to use some waterproof grease on the flanges upon ressembly to prevent water from leaking though the flanges.




Outer bearing can now be removed and replaced


We at ROUTE6x6 and RICAHRDS'S RELICS feel due to low cost of these bearings and high degree of effort to "get at them". We always replace old bearings with new ones.


Click here to go to the ATV Chassis parts page

Reassembly

Reassembly is a direct reverse of above steps:

With addition:

Obviously: Rusty axles should be sanded clean before reassembly

With bearings loosely mounted, slide axle through both bearings. Tighten mounting nuts. Axle should slide in and out of bearings with little effort. If not: Loosen flange mounting nuts on outer bearing and tap axle with a rubber mallet to change bearing position. Retighten nuts, check to see if axle will slide freely. If not loosen nuts and repeat procedure untill axle slides in and out freely.


Locking collar bearings will have to be "relocked"


1st: Make sure you have installed bearing with locking race outward. Then sliding locking collar into inner race of bearing as shown in photo.




Click on PHOTOS to see larger view


Take same punch and spin locking collar into the inner race untill it turns no more.

 

Note: Make sure you do not tap on hole that has threads for the set screw, use other hole.



Install set screw:

 

Note set screw is only used to keep locking from releasing from inner bearing, not to hold axle to bearing.

   


Final step:

Make sure all bolts are tightened, chain is still in alignment, on most machines it is possible to "move" the axles in and out depending on where you lock the bearings down to axle, therefore if chains are not in alignment, simply move axle in to out and relock locking collars and set screw bearings.

If you have any questions, you welcome to contact us at richard@route6x6.com
or call 812-944-1643 8am-6pm weekdays and will will help you.

Replacement parts available at RICHARD'S RELICS ATV Chassis parts page